Related Question Answers
It contains five specialty weeding tools, including fine tweezers, hook tweezers, weeder, piercing tool, and hook weeder. Use them to hold and lift intricate vinyl designs, pierce, lift or place cuts, and even weed trickier materials such as glitter vinyl effortlessly.
Vinyl is not a natural substance but is a synthetic man-made material. It is a type of plastic that is made from ethylene (found in crude oil) and chlorine (found in regular salt). When processed, both the substances are combined to form Polyvinyl Chloride (PVC) resin, or as is commonly referred to – Vinyl.
Glitter Vinyl: Cutting and Application Instructions
- Place vinyl liner side down onto LightGrip Mat.
- Select images and size and load the mat into your machine.
- Refer to Glitter Vinyl Kiss Cut Guide below to adjust machine settings (a kiss cut goes through the vinyl film and leaves the liner intact).
- Press the flashing Go button.
A number of common weeding tools are designed to ease the task of removing weeds from gardens and lawns. The fulcrum head weeder has a split tip like a serpent’s tongue, and a long thin handle. Many models have a curved piece of metal along the handle which is put against the ground while the tip is digging.
ORACAL 651, or permanent vinyl, uses an adhesive and has a variety of craft uses. ORACAL 651 is commonly used for outdoor crafts due to its weather-resistant qualities, such as car decals, exterior windows or signs, and wood signs. Heat-transfer vinyl, or “iron-on” vinyl, is used for fabric projects.
The Pin Pen™ is a game-changer for weeding vinyl, HTV, and other materials. The contoured pen housing holds a special replacement cartridge with a needle-sharp pinpoint that allows you to stab and grab and remove even the tiniest pieces of vinyl.
Steps to removing Heat Transfer Vinyl
Take your garment and lay it on an ironing board, and then place your iron on top. Allow it to get hot to really seal the design onto your piece of clothing. Once done, slowly begin to pick at the vinyl to help loosen and get it to remove.
Place your iron on vinyl plastic-side DOWN on your cutting mat. I often use my Cricut Brayer to help press my vinyl into my mat, particularly if my mat is on the older side. Insert the mat into the Cricut and press the arrow button on your Cricut. It should grip your cutting mat and bring it into the machine.
Cricut Maker cuts hundreds of materials quickly and accurately, from the most delicate paper and fabric to matboard and leather. Expandable suite of tools. With a wide range of tools for cutting, scoring, writing, and adding decorative effects, Cricut Maker grows with you as you learn each new craft.
Gently place the Transfer Tape (adhesive side down) over your design, starting in the center and moving out toward the edges. Use a craft stick or the Scraper found in the Cricut Basic Tool Set to burnish (rub or polish) the tape onto the vinyl. Peel the vinyl away from the liner at a 45-degree angle.
In many, if not most, iron-on vinyls, the vinyl side is matte and the carrier side is shiny. That’s why they say to cut it shiny or glossy side down on your mat. That way, your mirrored design gets cut into the vinyl itself, allowing you to remove the vinyl that does not need to be transferred to your project.
Best Types of Vinyl Decals for Cups
If I ever have an issue of vinyl coming up, it’s because the letter was super skinny or had an intricate loop at the end. The more surface area that the adhesive is on, the better it will adhere to the stainless steel or mug.
When using cricut transfer tape, stick it to a scrap piece of transfer tape a
few times before you use it on your actual vinyl so that the stickyness is reduced. 2. Burnish the vinyl onto the glass by rubbing a damp sponge over it. I find this more effective than just using my fingers to adhere it to glass.
Product description. Style Name:pretty prints. Full 12″ x 12″ washi sheets designed by Anna Griffin let you cut semi-opaque accents using any Cricut machine and the extensive Cricut Image Library. These translucent sheets have stylish, usable patterns perfect for layering and creating semi-opaque decorative accents.
Poor quality or low tack transfer tape (here’s the transfer tape I recommend) Too much pressure/thickness when cutting the vinyl which pushes it into the backing. Glitter vinyl seems to have more problems being picked up than regular adhesive vinyl.
If your Cricut Maker or Cricut Explore machine is tearing or dragging through the material, check the following: Make sure that you have selected the correct material setting in Design Space or that the Smart Set Dial is on the correct setting.